Services

General service, inspections, and diagnostics

Service calls and troubleshooting of any electrical issue

Whole-home electrical safety inspections

Pre-purchase/homebuyer electrical inspections and reports

Code compliance reviews and correction plans

Thermal imaging scans for hot spots

Circuit tracing and mapping

Labeling panels, breakers, and circuits

Load calculations and service sizing

Power quality analysis (voltage drop, harmonics, sags/swells)

Nuisance tripping diagnosis (AFCI/GFCI/breakers)

Intermittent fault isolation (loose neutrals, backstabbed devices)

Insulation resistance (megger) testing

Continuity and polarity tests

Grounding continuity verification

Voltage drop measurements and mitigation

Panel torque checks and retightening connections

Documentation/as-builts and redline updates

Insurance claim assessments after fire/water/storm events

 

Permitting, coordination, and compliance

Pulling permits and scheduling inspections

Utility coordination for service shut-off/turn-on

HOA/architect/GC coordination

Energy code compliance (lighting controls, wattage limits)

ADA/accessibility-related electrical modifications where applicable

 

Emergency and temporary services

24/7 emergency response

Storm, flood, or fire damage remediation

Temporary power setups (temp panels, spiders, GFCI temps)

Emergency lighting and receptacles for critical loads

Temporary generator hookup and safe isolation

Pump power for flood mitigation

 

Service entrance, meter, and main equipment

Service upgrades (e.g., 60/100/150 to 200/300/400 A)

Overhead service mast/weatherhead replacement

Service lateral/underground service repair and upgrades

Meter base/pan replacement and relocation

Main disconnect installation/relocation

Service grounding electrode system upgrades (ground rods, Ufer, water bond)

Bonding of water, gas, rebar/steel, CSST bonding clamps

Replacement of corroded service conductors and lugs

Service riser drip loops and clearances corrections

Whole-house surge protection at service equipment

 

Load centers and distribution

Main panel replacement/relocation

Subpanel installation (garage, addition, outbuilding)

Panel reconditioning (clean, torque, reorganize, label)

Breaker replacement (standard, tandem, AFCI, GFCI, DF, 2-pole)

Arc-fault and ground-fault protection upgrades

Interlock kits for generator backfeed compliance

Critical loads/essential circuits subpanel

Bus/stab repairs where allowed or panel change-out

Neutral/ground bar corrections and isolation in subs

Multi-wire branch circuit (MWBC) handle-tie/2-pole fixes

Load balancing across legs

Replacement of obsolete/dangerous panels (Zinsco, FPE, etc.)

 

Wiring, cabling, and raceways

New branch circuit installation (120/240 V)

Full or partial home rewiring

Knob-and-tube evaluation, remediation, or replacement

Aluminum branch circuit remediation (pigtailing, COPALUM/AlumiConn where permitted)

Replacement of damaged or rodent-chewed wiring

Routing NM-B/MC/EMT/PVC as appropriate

Concealed “old work” fishing and patch-minimized methods

Conduit installation (EMT, ENT, PVC, RMC) and fittings

Firestopping and draft sealing penetrations

Nail plates, staples, bushing and protection compliance

Junction box additions, extensions, and cover corrections

Splicing, pigtailing, and wirenut/ferrule terminations

Backstabbed device remediation (move to screw terminals)

Shared neutral and GFCI/AFCI compatibility fixes

Voltage drop mitigation with upsized conductors

Trenching and backfilling for underground feeds

Attic, crawlspace, and basement rough-ins

Bonding/grounding of metal boxes and raceways

 

Outlets, receptacles, and small devices

Install/replace standard receptacles

Tamper-resistant receptacles

Weather-resistant/outdoor receptacles with in-use covers

GFCI receptacles (kitchen, bath, exterior, garage, basement)

AFCI/GFCI or dual-function breaker solutions

Dedicated circuit receptacles (freezer, sump, server rack)

20A small-appliance circuits for kitchens

USB/USB-C charging receptacles

Recessed receptacles for wall-mounted TVs

Floor receptacles and pop-up boxes

Isolated ground receptacles (if specified)

Split/half-hot receptacles controlled by switches

Replacement of damaged/burned outlets

Re-termination, tightening, and polarity correction

Childproofing/outlet caps and safety plates

 

Switching and controls

Single-pole/3-way/4-way switch installs and corrections

Dimmers (incandescent, LED-compatible, ELV/MLV)

Fan speed controls

Motion/occupancy/vacancy sensors

Timers and astronomic timers

Photocell controls

Pilot light and locator switches

Smart switches, dimmers, and keypads

Scene control programming and integration

Low-voltage control relays and contactors

 

Interior lighting

Fixture installation and replacement (all types)

Recessed can/wafer light layouts and installs

Retrofit LED trims and conversions

Under-cabinet and toe-kick lighting

Cove and indirect lighting

Track, rail, and monorail lighting

Pendant and chandelier installs/height adjustments

Stair, hallway, and night lighting

Closet code-compliant lighting

Accent and display lighting

Art and picture lighting

Mirror and vanity lights

Entryway and foyer high-ceiling work

Dimming and color temperature tuning (if supported)

 

Ceiling fans and ventilation

Ceiling fan installation and balanced mounting

Fan-rated box upgrades

Fan/light combo wiring and controls

Bathroom exhaust fans with timer/humidity controls

Kitchen hood power and make-up air interlocks

Whole-house fans and attic ventilators

 

Exterior and site lighting

Porch, patio, and soffit lighting

Security and flood lighting with motion sensors

Dusk-to-dawn lighting

Post lights and pier mounts

Step and pathway lighting

Driveway and address lighting

Deck and railing lights

Flagpole lighting

Barn/carport/outbuilding lighting

 

Landscape and low-voltage lighting

Low-voltage transformer installation

Landscape/path/bollard lights and wiring

Smart/DMX/RGB landscape control integration

Waterproof splices and burial-rated methods

 

Kitchens and dining

Small-appliance circuits and counter receptacle layouts

Island/peninsula pop-ups and floor boxes

Microwave, range hood, and dishwasher circuits

Garbage disposal wiring and switch/air switch

Electric range/oven/cooktop (240 V) circuits

Built-in refrigerator and wine cooler circuits

Under/inside cabinet and toe-kick lighting

Pantry lighting and freezer dedicated circuits

GFCI/AFCI compliance updates

 

Laundry and utility

Washer and gas dryer circuits

Electric dryer (240 V) circuits

Ironing station power

Utility sink pump circuits

Water softener and filtration equipment power

 

HVAC and mechanical

Furnace/air handler circuits and service outlets

Condenser/heat pump disconnects and circuits

Mini-split indoor/outdoor units power

Boiler and circulator pump circuits

Radiant floor heat power and controls

Baseboard and wall heaters

Thermostat power (C-wire adds) and controls

HRV/ERV/whole-home dehumidifier circuits

Attic/basement dehumidifier dedicated circuits

 

Water heating and pumps

Electric tank and tankless water heater circuits

Heat pump water heater circuits

Recirculation pump power

Sump, sewage ejector, and grinder pump circuits

Well pump and pressure switch wiring

Irrigation controller power and pump starters

Radon mitigation fan power

 

Bathrooms and spa

GFCI-protected bathroom circuits

Lighting and ventilation combinations

Heated floor mats and thermostats

Bidet seat/GFCI outlets

Whirlpools, hot tubs, and spas wiring with GFCI and disconnects

Sauna heater circuits

Steam shower generator power

Pool equipment power (pumps, heaters, lights)

Pool/spa bonding and equipotential grids

Underwater light niche bonding and transformer installs

 

Garages, workshops, and outbuildings

Garage door opener circuits and receptacles

Workshop subpanels and dedicated tool circuits

Air compressor and dust collector circuits

240 V circuits for welders, saws, and chargers

Lighting upgrades and task lighting

Detached garage/shed/outbuilding feeders

Barn and agricultural outbuilding wiring (where permitted)

EV charging outlets (NEMA 14-50, 6-50, TT-30, etc.)

Level 2 EVSE hardwired installations

Load management devices for EVs

 

Backup power and energy storage

Inlet installation for portable generators

Manual transfer switches

Panel interlock systems

Whole-home standby generators with automatic transfer switches

Generator concrete pads and set, where offered

Load shedding/management for generator systems

Battery backup systems (Powerwall, Enphase, etc.)

Critical loads subpanel for storage systems

Maintenance and testing of generators/backup

 

Renewables and interconnection (varies by contractor)

Solar PV AC interconnection (breaker taps, line-side taps)

PV-ready subpanels and service upgrades

Rapid shutdown devices and labeling

Grounding/bonding for arrays and racking

Microgrid/non-export controls (where applicable)

 

Smart home, networking, and low-voltage (offered by many, though sometimes a separate license)

Smart switches, dimmers, plugs, and scenes

Smart panel/load control modules

Voice assistant integrations (Alexa/Google/HomeKit)

Smart thermostat installation and C-wire add-a-wire

Doorbells (wired/video) and chimes with transformers

Intercom systems power and rough-in

Structured cabling (Cat5e/Cat6/Cat6a), home runs to panel

Coax (RG6) cabling and splitters

PoE device cabling and injector power

Wi-Fi access point cabling and in-ceiling AP power

Network rack power and UPS receptacles

Camera power supplies and low-voltage feeds

Audio/video power and conduit pathways

TV mounting with recessed power/low-voltage pass-throughs

 

Fire, life safety, and security

Hardwired smoke alarms with battery backup and interconnect

CO alarms and combination units

Heat detectors for garages/attics where required

Strobe/horn devices where needed

Security system power supplies and dedicated circuits

Egress lighting and emergency lighting

Elevator/chair lift/stair lift power and controls

 

Specialty appliances and equipment

Built-in microwave and drawer microwave power

Double wall oven circuits

Warming drawer power

Ice maker and beverage center circuits

Trash compactor power

Central vacuum power units

Electric fireplace inserts and in-wall fireplaces

Outdoor kitchen equipment circuits

Greenhouse heaters and fans

Aquariums/terrariums dedicated circuits

Treadmills and home gym equipment circuits

Home office dedicated circuits and surge protection

Window AC power additions

Snow melt mats/cables and controls

Heat trace/pipe freeze protection circuits

Gate opener power and controls

Fence/lot lighting and power pedestals

 

Exterior power and site work

Exterior GFCI receptacles with in-use covers

Weatherproof boxes and fittings

RV/shore power pedestals and outlets

Boat lift and dock power (freshwater residences)

Post/column outlets

Holiday lighting outlets and switch controls

Yard, shed, and pergola power feeds

Trenching for landscape, irrigation, and outbuildings

Bonding of metal fences, rails, and pools

 

Repair, replace, and small jobs

Replace broken switches/outlets/plates

Repair loose or damaged conductors and terminations

Tighten loose neutrals and grounds

Replace light fixtures and ballasts/drivers

Re-seat or replace lampholders/sockets

Fix flickering lights and dimmer compatibility issues

Replace doorbell transformers and chimes

Secure loose boxes and device yokes

Add missing box fill extensions and covers

Replace corroded exterior boxes and fittings

Repair chewed or nicked cords (hardwired equipment)

Re-support sagging cable runs and conduits

Patch small access holes as part of scope (when offered)

 

Upgrades and modernization

Convert to LED lighting throughout

Add more circuits for modern loads

Add receptacles to meet spacing codes

Kitchen/bath remodel electrical rough-in and trim-out

Basement finish wiring

Attic and bonus room conversions

Open concept rewire after wall removals

Smart home retrofits and centralized lighting

Energy monitoring systems and CTs

Whole-home surge and point-of-use surge protection

Power factor and inrush mitigation for sensitive equipment

 

Safety, bonding, and grounding specifics

Correct bootleg grounds and open neutrals

Add equipment grounding conductors to old circuits

Bond CSST/gas piping and water piping

Replace old two-prong outlets appropriately

Install GFCI/AFCI where required by current code

Equipotential bonding for pools/spas/decks

Lightning protection system bonding (with LPS contractor)

Isolation and labeling of standby sources

 

Old-home and specialty remediation

Plaster-friendly old-work methods

Cloth/rubber insulation wiring replacement

BX/AC to modern NM transitions

Box fill and cubic-inch compliance fixes

Raised device rings for tile/backsplash changes

Sconce height/box relocation in masonry

Historic fixture restoration wiring (where offered)

Knob-and-tube insulation clearance solutions

 

Testing, maintenance, and optimization

Annual safety checkups

GFCI/AFCI testing and replacement schedule

Generator exercise/testing programs

Battery system firmware and functional checks

Lighting control reprogramming

Panel infrared scan and torque maintenance

Surge protection inspection and replacement after events

Load logging for EV or appliance additions

 

Documentation, education, and support

Panel directory creation and cleanup

Circuit maps and labeling inside home

Homeowner education on breaker reset and safety

Operation guides for smart systems and scenes

Maintenance schedules for alarms and detectors